|
|
Technical specification |
| With an Xstreme you get a lot for your money |
|
Click to enlarge image |
|||||||||||||||||||||
|
 |
||||||||||||||||||||
| Installation |
| As an unvented cylinder of more
than 15 litres capacity, Xstreme
must be installed by a competent installer in accordance with
local Water Supply (Water Fittings) Regulations and Building Regulations*
*England and Wales - G3, Scotland - P3 |
| Cold water control |
| Combination inlet group
regulating the hot water supply to a static pressure of 1.5bar at the
cylinder.
Compatible with gas or oil fired boilers either sealed system or open vent type. If you require an open vented model please add OV to the model size - or SS for a sealed system. |
Price List - June 2007
| Model Options (Prices include VAT, delivery and ancillary components listed above) | |||||||||
| Indirect | |||||||||
|
Model |
H (mm) | W (mm) | D (mm) | Selection Guide | Heating from cold time (*1) (mins) | Recovery time (*2) (mins) | Hourly hot water output (*3) (litres) | ||
| 15kW boiler | 25kW boiler | 35kW boiler | |||||||
| AX125 IND | 907 | 595 | 410 | 2/3 Bedrooms, 1 bath & shower | 11 | 7 | 339 | 505 | 670 |
| £850.24 | |||||||||
| AX150 IND | 1140 | 595 | 410 | 2/3/4 bedrooms, 1 bath & 2 showers | 14 | 9 | 367 | 533 | 698 |
| £882.49 | |||||||||
| AX180 IND | 1370 | 595 | 410 | 3/4 bedrooms, 1 bath & 3 showers | 17 | 11 | 394 | 560 | 725 |
| £945.02 | |||||||||
| AX210 IND | 1600 | 595 | 410 | 3/4/5 bedrooms, 2 baths & 2 showers | 16 | 10 | 420 | 586 | 751 |
| £977.01 | |||||||||
| AX240 IND | 1950 595 | 595 | 410 | 4/5 bedrooms, 3 baths & 1 shower | 20 | 13 | 464 | 630 | 795 |
| £1051.89 | |||||||||
| Direct | ||||||||||||||||
| Model | H (mm) | W (mm) | D (mm) |
|
||||||||||||
| AX140 D | 1370 | 595 | 410 | |||||||||||||
| £827.10 | ||||||||||||||||
| AX175 D | 1600 | 595 | 410 | |||||||||||||
| £865.92 | ||||||||||||||||
| AX210 D | 1950 | 595 | 410 | |||||||||||||
| £895.85 | ||||||||||||||||
| Related Literature: | Xstreme Technical.pdf | Xstreme Brochure.pdf |
| Pressure testing |
| All cylinders are 100% factory pressure tested to ensure trouble-free operation. |
| Electrical |
| Connection is direct to terminals in the immersion heater which must be permanently connected to the supply through a double pole linked isolating switch with a minimum breaking capacity of 16A. On indirect models, controls should be wired to the boiler, programmer etc in accordance with the control scheme being used. All electrical installations must conform to the current IEE Wiring Regulations. |
| Flow rates |
| The Xstreme will provide very high flow rates under adequate supply conditions. Minimum supply pressure should not be less than 2 bar. (The Xstreme will operate at lower values but outlet flow rates will be reduced, especially with multi draw-offs.) |
| Plumbing |
| Inlet / Outlet: 22mm copper tube
suitable for push-fit connections or compression fittings.
Indirect coil: 22mm copper tube suitable for push-fit connections or compression fittings 1/2" T&P relief valve 15mm compression outlet. |
| Tundish |
| 15mm inlet and 22mm compression outlet. |
| Water expansion |
| A potable water expansion vessel is supplied with each Xstreme unvented cylinder. This can be mounted on top of the unit for ease of access and maintenence. |
| Insulation |
| High density CFC-free polyurethane foam within steel outer casing (ozone depleting potential ODP = zero) |